Honda Odyssey and Pilot Forum
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
Help
Search
Calendar
Login
Register
Honda Odyssey and Pilot Forum
»
General Category
»
Odyssey FL250
»
FL250 Driven Pulley from Gearbox HELP
« previous
next »
Print
Pages: [
1
]
Author
Topic: FL250 Driven Pulley from Gearbox HELP (Read 5124 times)
RickieLee
Newbie
Posts: 17
Karma: 1
Nanuck of the North MI Woods
FL250 Driven Pulley from Gearbox HELP
«
on:
January 06, 2012, 04:18:07 PM »
Hi! I can't figure out out how to separate the driven pulley from the gear reduction box? I have the gearbox and pulley on a table but can't figure out how to separate them??
Thanks!!
Logged
whammo77
Newbie
Posts: 33
Karma: 0
Re: FL250 Driven Pulley from Gearbox HELP
«
Reply #1 on:
January 06, 2012, 07:11:16 PM »
Do you have one of the Clymer manuals??? I can't rememebr if it tells in there or not. There is certain stuff, such as removing the driven clutch, that it just says "You are better off taking it to a certified Honda dealer"..... Ugh.....
Logged
RickieLee
Newbie
Posts: 17
Karma: 1
Nanuck of the North MI Woods
Re: FL250 Driven Pulley from Gearbox HELP
«
Reply #2 on:
January 06, 2012, 09:34:07 PM »
I have the Honda manual, but no help there!
Logged
LiveWire
Administrator
Hero Member
Posts: 1077
Karma: 20
Re: FL250 Driven Pulley from Gearbox HELP
«
Reply #3 on:
January 07, 2012, 12:00:39 PM »
The input is a 3/4 keyed shaft. The clutch was meant to slide off once the bolt was removed. Rust is holding it on. Get an air hammer kit. They are cheap to buy. Put a bolt in the end of the shaft you are not worried about losing. Don't use a washer. Have someone pull on the clutch with two hands. Turn the power down on the air hammer and use it on the bolt head. Turn up the power little by little until the clutch starts to move off. Once it starts moving, it will move faster and faster with the same air hammer setting.
Logged
Honda Odyssey FL250 Parts
Honda Odyssey FL350
R Parts
Honda Pilot FL400R Parts
RickieLee
Newbie
Posts: 17
Karma: 1
Nanuck of the North MI Woods
Re: FL250 Driven Pulley from Gearbox HELP
«
Reply #4 on:
January 07, 2012, 03:36:15 PM »
Thanks Livewire! I read ALOT of the info you give over on minibuggy too and you seem very knowledgeable and willing to share.
I appreciate your help!!
Logged
RickieLee
Newbie
Posts: 17
Karma: 1
Nanuck of the North MI Woods
Re: FL250 Driven Pulley from Gearbox HELP
«
Reply #5 on:
January 10, 2012, 09:12:46 PM »
Again THANKS Livewire, the hammer drill method worked, I had the sparation in minutes with it!!
Logged
LiveWire
Administrator
Hero Member
Posts: 1077
Karma: 20
Re: FL250 Driven Pulley from Gearbox HELP
«
Reply #6 on:
January 11, 2012, 10:11:41 AM »
Good to hear.
Logged
Honda Odyssey FL250 Parts
Honda Odyssey FL350
R Parts
Honda Pilot FL400R Parts
Print
Pages: [
1
]
« previous
next »
Honda Odyssey and Pilot Forum
»
General Category
»
Odyssey FL250
»
FL250 Driven Pulley from Gearbox HELP