Author Topic: fl350 no spark  (Read 3092 times)

sgtsrwalker

  • Newbie
  • *
  • Posts: 5
  • Karma: 0
    • View Profile
fl350 no spark
« on: April 09, 2011, 08:44:52 PM »
hi im new to this forum and was looking for some help ive had this fl350 sence i was 14 and im 26 now i took it apart to paint the frame and never finshed it to know it was apart for 8 years and ive droped about 2500 into it. the problem is i took it for a ride around the block then it died and im getting no spark ive tryed to just pull start it and that doesnt work ether ive traced all the wires and there all good wires. I think its the cdi but i do not know how to tell if it is the cdi or not please help thanks

hoodlum

  • Administrator
  • Hero Member
  • *****
  • Posts: 857
  • Karma: 11
    • View Profile
fl350 no spark
« Reply #1 on: April 10, 2011, 06:28:36 AM »
Do you have a manual? It gives detailed instructions for checking the cdi,coil,pulse generator and alternator....These test will let you know where your problem lies......
Hoodlum

sgtsrwalker

  • Newbie
  • *
  • Posts: 5
  • Karma: 0
    • View Profile
fl350 no spark
« Reply #2 on: April 10, 2011, 02:20:51 PM »
ive tryed but it shows that the coil which is new is bad and cdi and pulse generater and altinator is bad in the book it says {The CDI unit is fully transistorized.
For accurate testing, it is necessary to use a specified electric
tester. Use of an improper tester may give a false reading.
Use Sanwa Electric Tester (07308-0020000) or Kowa
Tester (TH - 5H - 1 ) or Kowa Digital Multi-Tester (0741 1 - ,
0020000 or KS-AHM-32-003: U.S.A. only).} so i think thats why im getting crazy readings

sgtsrwalker

  • Newbie
  • *
  • Posts: 5
  • Karma: 0
    • View Profile
fl350 no spark
« Reply #3 on: April 10, 2011, 02:22:48 PM »
ive tryed two differant good quality meters one was even new out the box

sgtsrwalker

  • Newbie
  • *
  • Posts: 5
  • Karma: 0
    • View Profile
fl350 no spark
« Reply #4 on: April 10, 2011, 06:20:57 PM »
ive checked the kill switch and i only get continuity when switch is off. i get continuity threw the two prongs on the spark plug coil. i have checked the wire going to the cdi to the coil to its good . it sucks after all this work and transporting it from mass to az and its dead .what a downer i could of got another one for what ive put into it .

hoodlum

  • Administrator
  • Hero Member
  • *****
  • Posts: 857
  • Karma: 11
    • View Profile
fl350 no spark
« Reply #5 on: April 10, 2011, 07:15:01 PM »
Quote from: "sgtsrwalker"
ive tryed but it shows that the coil which is new is bad and cdi and pulse generater and altinator is bad in the book it says {The CDI unit is fully transistorized.
For accurate testing, it is necessary to use a specified electric
tester. Use of an improper tester may give a false reading.
Use Sanwa Electric Tester (07308-0020000) or Kowa
Tester (TH - 5H - 1 ) or Kowa Digital Multi-Tester (0741 1 - ,
0020000 or KS-AHM-32-003: U.S.A. only).} so i think thats why im getting crazy readings


Any digital volt meter that will read ohms should check the everything except the cdi....Does the 350 have fuses like the pilot does? If so,have you checked them? They are by the battery on the pilot....

sgtsrwalker

  • Newbie
  • *
  • Posts: 5
  • Karma: 0
    • View Profile
fl350 no spark
« Reply #6 on: April 10, 2011, 07:59:53 PM »
ya it has one and i checked to made shore it works.